|
|
Joined:
March 2002
Posts: 15682
Location: SoCal | Check this Viper out
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&category=2384&item=3760327917&rd=1
What kind of wood is the body? |
|
| |
|
Joined:
August 2003
Posts: 4619
Location: SoCal | purdy ain't it... |
|
| |
|
Joined:
May 2002
Posts: 3005
Location: Las Cruces, NM | As I said in the other post, I sure like it. |
|
| |
|
Joined:
August 2002
Posts: 8307
Location: Tennessee | Text of the posting says it's maple ... I read that Ovation made a very small number of Vipers with maple bodies, could this be one of them?
I like the opening price! Hope it bids up higher. A mahogany bodied Viper went for almost $600 a couple of months back. Makes the other one on eBay (with the white pickguard) look like a steal at $340. |
|
| |
|
Joined:
February 2002
Posts: 5750
Location: Scotland | The vast majority of Vipers were made with Maple bodies, and I've seen a handful with pretty spectacular figure in the bodies & necks. They were originaly specified with Alder as the body material but they went to Maple pretty early in production. The problem with Maple is that it can be very dense and consequently very heavy. There are some Vipers out there that weigh a ton. |
|
| |
|
Joined:
September 2003
Posts: 9301
Location: south east Michigan | I have wondered what type of fantasic wood grain lies underneath the finish of my white Breadwinner.
This may be blasphemy, but has anyone ever tried to take the white or (gasp) TAN finish off a Breadwinner to see what is underneath? |
|
| |
|
Joined:
June 2002
Posts: 6202
Location: Phoenix AZ | Moody - Is this a Viper SUPER Deluxe ???? |
|
| |
|
Joined:
December 2003
Posts: 13997
Location: Upper Left USA | Brad,
I stripped a Sunburst Viper body (Alder or Ash, see pics) and it had intersting grain - as well as being a four piece board.
I would think they are all purposely done for cost savings - black or solid color being the multi board or odd grained.
This one was special from the day it started! |
|
| |
|
Joined:
January 2003
Posts: 1498
Location: San Bernardino, California | I've seen anywhere from one piece to seven pieces of wood for viper bodies. |
|
| |
|
Joined:
February 2002
Posts: 5750
Location: Scotland | Slipkid, every Breadwinner, Deacon, Preacher or Magnum I've seen, and that's a lot of guitars, have had the body made from a single piece of Honduran mahoghany. Refinish a Breadwinner with a clearcoat & basically you have a Deacon. These days PRS and the like would kill for lumber of that quality in that width. |
|
| |
|
Joined:
January 2003
Posts: 1498
Location: San Bernardino, California | Does anyone know what kind of finish Ovation used for the satin finished bodies? I just picked up a Magnum IV that has a couple of minor finish flaws and I was wondering if it was safe to use swirl remover on it. |
|
| |
|
Joined:
January 2002
Posts: 14127
Location: 6 String Ranch | It was a satin urethane of some type on the mag4. This VIper on ebay is maple. Many were alder in the beginning but there was too much variation in the wood grain so the switch was made to maple. I think there were some ash and a few mahogony. Lots of the breads and deacons were two piece but all were mahogony |
|
| |
|
Joined:
December 2003
Posts: 13997
Location: Upper Left USA | Sorry to bring it back to me (It's all about me!) but is this body Alder or Ash:
Viper Project |
|
| |
|
Joined:
November 2002
Posts: 3666
Location: Pacific Northwest Inland Empire | I'm betting alder. Your pickguard looks like an oak pattern. Interesting. Heard about "fuming" your wood to accentuate the grain pattern? |
|
| |
|
Joined:
June 2004
Posts: 3
| Hi:
I have a black breadwinner and am intrigued that there might be a one-piece gorgeous mahogany body underneath.
In January I will have time for a guitar project and would like to refinish this guitar. I'd like to go clear with it. Do you guys have any serious tips to make this metamorphosis go smoothly? I can do the solder gun thing, but have never done refinishing. And of course I would rather leave the guitar alone than ruin it.
Thanks-- Mel |
|
| |
|
Joined:
December 2001
Posts: 10583
Location: NJ | usually guitars that were painted black had some sort of blem. |
|
| |
|
Joined:
May 2002
Posts: 3005
Location: Las Cruces, NM | Mel
If you are not a collector who wants original guitars, I would say go for it, if it is a piece of cheap wood, there is plenty of black paint on the market to cover up your disappointment. |
|
| |
What kind of wood?
